·Golf Toolbox Team

Wedge Bounce and Grind Explained: Match Wedges to Your Swing

This page contains affiliate links. If you buy through one, Golf Toolbox may earn a commission.

Bounce is the angle between the ground and a line running from the leading edge of a wedge down to the lowest point of the sole. It is the reason a wedge glides through sand and turf instead of digging. Pick too little for your swing and conditions and the club digs. Pick too much and the leading edge sits up off the ground and you thin the ball. Grind is the shaping of the sole that decides how that bounce behaves when you open the face or lean the shaft. Get both right and your short game gets easier without changing your swing.

What Bounce Does

Set a wedge on the ground at address and look at the sole from the toe end. On most wedges the leading edge sits slightly above the lowest part of the sole. That angle is bounce, and it is measured in degrees. When the club enters the ground, the trailing part of the sole makes contact first and pushes the club back up, so the head skims through rather than burrowing.

Wedges are commonly grouped as low, mid and high bounce. Low bounce keeps the leading edge close to the ground, which helps on firm turf and tight lies and for players who like to open the face. High bounce keeps the leading edge up, which helps in soft turf, fluffy sand and for steep swings. Mid bounce covers the widest range of players and is the safest starting point if you are unsure.

Sole Width Changes Effective Bounce

Two wedges with the same bounce number can play differently because of sole width. A wider sole spreads the bounce over more surface, so it resists digging more than the number suggests. A narrow sole with the same bounce cuts into the ground more easily. That is why a sand wedge with a wide sole can feel forgiving in bunkers with only a moderate bounce number, and why a narrow-soled lob wedge can feel sharp on soft turf.

When you compare wedges, read the bounce number and then look at the sole itself. Width and bounce together tell you how the club will behave.

Grind: Shaping the Sole

A grind removes material from the heel, toe or trailing edge of the sole. The goal is to change how the bounce meets the ground when the face is opened or closed. A wedge with heel relief lets you open the face without the leading edge rising too far off the turf, which helps on flop shots and tight lies. A full sole with little relief keeps all of its bounce working on square-faced full swings and bunker shots.

The Titleist Vokey SM10 is the usual reference point for grind choice. Vokey offers it in several grinds, each pairing a bounce range with a sole shape, so you can pick the combination that fits your swing and your course. It lists around $180 in our catalog, with spin milled grooves and a forgiveness rating of 6 out of 10. Our skill ratings place it from intermediate through scratch.

If you mostly hit square-faced pitches and full shots, a fuller sole is the simpler choice. If you open the face a lot around the green, look for a grind with heel relief.

Diggers and Sweepers

Your angle of attack matters as much as your conditions. A digger has a steep swing that takes deep divots, often with the shaft leaning well forward at impact. Diggers usually benefit from more bounce, because the extra angle stops the club from burrowing. A sweeper has a shallow swing that brushes the turf and takes thin divots or none at all. Sweepers usually do better with less bounce, so the leading edge can get under the ball without the sole skipping off the ground first.

Look at your divots after a range session on grass. Deep, thick divots point to more bounce. Shallow scrapes point to less. Then factor in your course. Soft, wet turf and soft sand push you toward more bounce. Firm, dry fairways and firm, thin bunkers push you toward less. A steep player on a soft course usually wants plenty of bounce. A shallow player on a firm, fast course usually wants very little.

Full-Face Grooves and Open-Face Shots

When you open the face for a high pitch or a bunker shot, contact tends to move toward the toe. On many wedges the grooves stop short of the toe, so those shots catch a smooth part of the face. The Callaway Jaws Raw Full Face runs its groove pattern across the entire face to deal with this. It also has a raw finish that rusts over time, and the product description says that rusting face gives progressively more spin. It lists around $175 in our catalog with a forgiveness rating of 7, one point higher than the SM10, and the same intermediate through scratch skill range.

Full-face wedges suit players who hit a lot of open-faced shots with their higher lofts. For a gap wedge that mostly makes full swings, a standard groove layout does the job.

Gapping From Your Pitching Wedge

Bounce and grind decide how a wedge behaves. Loft decides how far it goes. Start your wedge setup from your pitching wedge, not from the sand wedge you already own. Many modern iron sets have strong pitching wedge lofts, and that can leave a large distance gap to a traditional sand wedge.

Find your pitching wedge loft on the manufacturer's spec sheet, then build down in even steps. A common rule of thumb is four to six degrees of loft between wedges, which usually produces fairly even distance gaps on full swings. That might mean a gap wedge, a sand wedge and a lob wedge, or only two wedges if your pitching wedge loft is weaker. Check carry distances on a launch monitor or a range with marked targets, and adjust if two clubs land in the same place.

Then assign bounce by job. The gap wedge usually needs less bounce because it is played mostly from the fairway with full swings. The sand wedge often carries the most bounce because it handles bunkers and soft lies. The lob wedge can go either way, with lower bounce for firm courses and open-face shots, and higher bounce for soft conditions and steep swings.

Where to Start

Write down three things: how deep your divots are, how firm your home course plays, and your pitching wedge loft. That is enough to pick a bounce range and a gapping pattern. Our club fitting tool covers drivers, irons and shafts rather than wedges, but run it before you settle on new wedges, because the iron set you end up with decides where your wedge gaps start. Then hit your two or three candidate grinds from real turf, because hitting mats hide digging and make every sole feel forgiving.

Ready to improve your game?

Use our free tools to get personalized recommendations and track your progress.

As an Amazon Associate I earn from qualifying purchases.